Skip to content

Hardware Specifications

Vendor/Brand UFiber
Model UFiber UF-Instant
Chipset Realtek RTL9601CI
Flash 16 MB
RAM 64 MB
System Linux (Luna SDK)
SFP interfaces 1 Gbps only, no HSGMII
Optics SC/APC
IP address 192.168.1.1
Web Gui ✅ user ubnt, password ubnt
SSH ✅ user ubnt, password ubnt, disabled by default
Telnet
Serial ✅
Form Factor miniONT SFP

Hardware Specifications ​

Vendor/BrandUFiber
ModelUFiber UF-Instant
ChipsetRealtek RTL9601CI
Flash16 MB
RAM64 MB
SystemLinux (Luna SDK)
SFP interfaces1 Gbps only, no HSGMII
OpticsSC/APC
IP address192.168.1.1
Web Gui✅ user ubnt, password ubnt
SSH✅ user ubnt, password ubnt, disabled by default
Telnet
Serial✅
Form FactorminiONT SFP

Firmware is interchangeable with: ​

Info

The UFiber UF-Instant can be used as universal GPON stick with V2801F rootfs, but only with stock UF kernel (4.3.1/4.4.2): needed for Laser controller.

List of partitions ​

devsizeerasesizename
mtd00004000000001000"boot"
mtd10000200000001000"env"
mtd20000200000001000"env2"
mtd30003c00000001000"config"
mtd40030000000001000"k0"
mtd5004b000000001000"r0"
mtd60030000000001000"k1"
mtd7004b000000001000"r1"
mtd80001000000001000"hw"
mtd90001000000001000"sec"
mtd100000100000001000"Partition_010"
mtd110000100000001000"Partition_011"
mtd120030000000001000"linux"
mtd13004b000000001000"rootfs"

This stick supports dual boot: k0 and r0 contain kernel and rootfs of the first image, k1 and r1 of the second one. A full flash dump (with flash_all.xml) is available in the RTL960x repository[1]: SSH is disabled in the stock configuration and had to be enabled to make the dump.

sh
ssh ubnt@192.168.1.1 'cat /dev/mtd0' > dev_mtd0

Serial ​

The UART pads are, from the front (SC connector) to the back (SFP connector): GND, VCC, RX, TX[1:1]. On the RTL9601CI (76 pins) the UART is on the pins 12 (TX) and 13 (RX)[2].

Know Bugs ​

VLAN swap issue (MEID 171), auto-sensing mode to switch between SGMII/HiSGMII

You should use the VID/VLAN shown by executing the command omcicli mib get 84 via telnet to bring up PPPoE

The stock firmware supports only the PPTP, and only on the LAN 1: it does not support the VEIP nor the 4-port emulation[3].

Miscellaneous Links ​


  1. UF-Instant flash dump, Anime4000/RTL960x https://github.com/Anime4000/RTL960x/tree/main/Firmware/UF-Instant ↩︎ ↩︎

  2. UART, Anime4000/RTL960x https://github.com/Anime4000/RTL960x/blob/main/Docs/UART.md ↩︎

  3. Hacking RTL960x, Anime4000/RTL960x https://github.com/Anime4000/RTL960x ↩︎

Copyright © 2022-2026. The documentation hereby found is distributed under the terms of the MIT License. Any external reference, link or software retains its original license and is not under the control of this website. Privacy Policy.